Drives and Control Solutions

Motors, Control Solutions, Power Transmission and Advanced Motion Technology                                                                 

April 21, 2020

By Mike Keefe

What Are Motor Duty Cycles?

When selecting a motor, it is important to consider the required duty cycle to ensure the motor can meet the needs of the application.  This blog post and the accompanying light board video will provide a basic introduction to motor duty cycles and a few of the most common types of duty cycles.

The International Electrotechnical Commission (IEC) defines eight classifications for duty cycle which are grouped by continuous, short term, or periodic cycles.  These cycles refer to the sequence and durations in time of all aspects of a typical operation, including starting, running with no load, running with full load, electric braking, and rest.  These operations are viewed by how they affect the motor temperature in order to determine if the selected motor is correct for the application, if increased cooling such as a forced ventilation fan is required, or if a whole new motor should be used.

#1 Continuous Duty (S1)

The first, and simplest, type of motor duty cycle is continuous duty.  This is also referred to by its abbreviated name, S1 duty (Figure 1).  In this type of operation, the motor runs with a constant load for a long enough duration so that it reaches thermal equilibrium.  This also assumes the starting of the motor can be considered to have a negligible effect on the motor temperature.  An example of S1 duty would be a fan that is switched on and then let to run non-stop

#2 Short Time Duty (S2)

Motor-Duty-Cycles_Short-Time-Duty.jpg

The second type of motor duty cycle is short time duty.  Similar to continuous duty, this operation runs with a constant load.  Unlike continuous duty, it is shut off before it reaches thermal equilibrium.  The motor is then allowed to rest long enough for it to reach ambient temperature.  Short time duty is designated by S2 followed by the number of minutes in the cycle (S2 30 minutes).

Periodic Duty (S3-S8)

Periodic duty refers to the designations S3-S8.  These include cycles with and without rest that have starting, electric braking, and/or changing speeds/loads.  Throughout all of these designations, the various operations of the cycle are repeated over time and the motor is not allowed to reach thermal equilibrium.

#3 Intermittent Periodic Duty (S3)

Motor-Duty-Cycles_Intermittent-Periodic-duty-graph.jpg

Intermittent periodic duty is the simplest type of periodic duty.  This sequence of identical cycles each contain a period of constant load and a period at rest.  This is very similar to S2 duty, but differs because it never reaches ambient temperature during its rest period.  This duty cycle is abbreviated as S3 followed by the percentage of time under load (S3 xx%, where the % = ∆Tc/T).  An example of intermittent periodic duty could be a conveyor that runs at constant intervals with the same loading.

#4 Continuous Operation with Electric Braking (S7)

Motor-Duty-Cycles_Continuous-Operation-with-Electric-Braking.jpg

The final example of motor duty cycle is continuous operation with electric braking.  This cycle includes a sequence of starting, constant load, and electric braking.  Additionally, there is not time during the operation for rest.  This type of duty cycle is abbreviated as S7 followed by the moment of inertia of the motor and load (Jm and JL).

The other periodic duty cycles S4-S6 and S8-S9 as similar to S3 and S7, but can be done with or without rest, starting, braking, and loading.

Conclusion

When purchasing a motor, it is important to consider the required operation and declare the duty cycle.  This ensures the proper motor is selected for the application.

Source


Editor's Pick: Featured Article


Motor Duty CyclesWhat Are Motor Duty Cycles?

When selecting a motor, it is important to consider the required duty cycle to ensure the motor can meet the needs of the application.  This blog post and the accompanying light board video will provide a basic introduction to motor duty cycles and a few of the most common types of duty cycles.

The International Electrotechnical Commission (IEC) defines eight classifications for duty cycle which are grouped by continuous, short term, or periodic cycles.  These cycles refer to the sequence and durations in time of all aspects of a typical operation, including starting, running with no load, running with full load, electric braking, and rest. 

Read More

 

 


Motor Feature


Servo MotorsThe ability to size servo motors correctly is imperative for motion-controlled applications, and it can be much more involved than sizing AC induction motors. Acceleration, deceleration, and running torque must still be taken into account, but the servo’s ability to dynamically control the load’s speed and position is also important. During acceleration and deceleration, peak and nominal running torque measurements must be calculated to ensure that the servo motor does not overheat during use. In addition, inertia matching between the motor and load is necessary to ensure optimum response and system performance.

 

 

Product News

  • Prev
Single Phase Power Solutions introduces a 75 hp single-phase electric motor to power industrial ...
Festo is meeting the need of the North American automotive sector for a powerful yet flexible valve ...
You may view your HMI software as the tool that puts production data in front of workers at ...
AMT series encoders from CUI Devices are advanced capacitive encoders with a variety of uses. AMT ...
The Drives & Motion Division of Yaskawa America, Inc. is proud to release Yaskawa Compass, a ...
Mitsubishi Electric Automation, Inc. recently released the newest addition to its lineup of ...
Parker Hannifin has introduced the Parker Service Master CONNECT, a strong diagnostic measuring ...
Synchronous drive belts and pulleys utilize teeth to prevent slippage and unwanted speed ...
ABB has launched its newest automated data acquisition and lab reporting solution, offering pulp ...
B&R enables machine builders to establish a continuous connection to plants and machinery in ...

FR-E800 Variable Frequency DriveMitsubishi Electric Automation, Inc. recently released the newest addition to its lineup of variable frequency drives, the FR-E800 Series. The micro-drive features a built-in PLC, and will include safety functionality meeting IEC 61508 standards and support various networks, including Ethernet/IP, MODBUS/TCP, and the soon-to-be-released CC-Link IE TSN. The FR-E800 Series is designed for engineering, technology, and product managers in industries such as packaging, material handling, food and beverage, and water and pumping, as well as those who are adopting PM motors to improve their energy efficiency.

Read more

 

 

 

 

 

 

Latest News

  • Prev
ABB Motion Canada alongside our HVAC Partners nationwide has introduced a special program for our ...
Brock Solutions is pleased to announce the recent award by the Region of Peel of the Clarkson and ...
This webinar (Friday April 17, 2020 at 11:00am - 12:00pm EDT) will review simple and easily ...
ABB is proud to announce it has been selected as one of Canada’s Best Employers by Forbes Magazine ...
Keeping pace with significant advances in motor speed control technologies, the International ...

Rittal & EPLAN Pump out a Powerful Solution for Metro Vancouver

Kerrwil Publications Great Place to Work. Certified December 2019 - December 2020

538 Elizabeth Street, Midland,Ontario, Canada L4R2A3 +1 705 527 7666
©2020 All rights reserved

Use of this Site constitutes acceptance of our Privacy Policy (effective 1.1.2016)
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Kerrwil